top of page

The Fresh Water Generator: Everything You Need to Know

Sep 22
16 min read

Fresh water is one of the most critical resources aboard any ship, and producing it reliably at sea is a genuine engineering challenge. The fresh water generator, also called an evaporator, is the equipment that solves this problem by converting seawater into usable fresh water. This guide covers the subject in full detail, from the basic need for onboard water production to the construction, operation, and maintenance of the different types of generators used across the shipping industry.

Why Ships Need Onboard Water Production

A considerable amount of fresh water is consumed aboard a ship. The crew consumes an average of 100 liters per head per day. On a steam ship, meaning a vessel whose main propulsion is a steam turbine, or a large tanker with steam turbine driven cargo oil pumps, boiler consumption can reach as high as 30 tons per day.

Sufficient potable water can be taken on in port to meet crew and passenger requirements, but this water is generally too poor in quality for use in water tube boilers. As a result, it is common practice to load only a minimal supply of potable water and generate the rest through the distillation of seawater. It is also a statutory requirement for ships to carry a distillation plant for emergency use, even if sufficient potable water has already been loaded.


Uses of Fresh Water on Ships

  • Machinery cooling

  • Boiler feed water

  • Washing decks and cargo tanks

  • Galley operations

  • Hot water supply

  • Domestic purposes, including bathrooms, toilets, and laundry

  • Sampling and operating various machinery systems


Objectives of Evaporators

  • Produce water in excess of daily consumption

  • Remove salt and solids from seawater

  • Treat and store the generated water

  • Treat water for bacterial contamination


Two primary methods are used onboard to achieve these objectives: distillation and reverse osmosis.


Distillation Systems

Distillation is the process of producing pure water from seawater by evaporating it and then re-condensing the vapor. Distilled water is produced by evaporating seawater through either a boiling process or a flash process. This evaporation reduces the dissolved solids content of seawater, which is around 32,000 parts per million, down to just one or two percent in the resulting distilled water.


Fresh water is generally produced onboard through evaporation because two things are available in abundance on a ship: seawater and heat. Seawater is evaporated using heat from an available source, then cooled again by seawater, and the cycle repeats.


The Two Distillation Processes

Boiling Process: In this method, the evaporator boils seawater at the saturation temperature corresponding to the pressure inside the vessel. This is known as a boiling evaporator. In a boiling evaporator, water is maintained continuously at its saturation temperature, meaning latent heat is being supplied.

Flash Process: In contrast, a flash evaporator supplies sensible heat rather than latent heat, causing water to flash into vapor when it moves into a lower pressure chamber.


Submerged Type Boiling Evaporator


The submerged tube type boiling evaporator was used extensively for many years, though it has notable drawbacks. These units were bulky and heavy, their thermal performance was relatively poor, and they required frequent descaling, usually through physical effort. In the absence of constant and careful attention, carry over of seawater into the distilled water side was always a risk.


Construction and Working Principle

A single effect boiling evaporator consists of a vertical cylindrical shell. The lower half forms the water space, which houses steam heated copper coils, while the upper half is the vapor space and contains a baffle plate to scrub off any water particles that might rise with the vapor.


Seawater is pumped into the evaporator, and the hot coils cause the water to boil, with the boiling temperature depending on the saturated vapor pressure inside the shell. The vapor produced passes through the vapor valve at the top and is led to a condenser, where it is condensed into fresh water. As the seawater boils off as vapor, salt and other solids remain behind, increasing the density of the water in the evaporator. To maintain a steady, low density, the evaporator is run with a constant blow down through a brine ejector.


Key Components

  • A steam valve to the coils, plus a steam pressure gauge to indicate heating steam pressure

  • A reducing orifice between the coil and steam valve to limit steam flow in case of a burst coil

  • A drain valve at the coil outlet

  • A feed check valve with a float controlled feed regulator

  • A water gauge glass to indicate water level

  • A vapor valve at the top of the evaporator, with a compound type vapor pressure gauge that can read even below atmospheric pressure

  • A pair of spring loaded safety valves to protect against excessive pressure

  • A brine ejector to maintain constant blow out and steady density


Boiling Process Evaporator (Low Pressure Evaporator) and Freshwater Generator

In some boiling type evaporators, seawater is boiled using a heating coil while pressure inside the evaporator shell is reduced, allowing boiling to occur at around 40 to 60 degrees Celsius. This design offers better economy than the submerged tube type described earlier.


Such plants are widely used for three main reasons:

  1. Greater control over the type of scale formed

  2. The heating medium can operate at relatively low temperatures, such as diesel engine jacket water or waste steam

  3. Improved heat transfer across the heating element, due to a higher temperature difference at lower pressures


Freshwater Generator: Plate Type


Heat from diesel engine cooling water is used to evaporate a small fraction of the seawater feed inside the plate type evaporator. Unevaporated water is discharged as brine through the brine ejector.

Evaporated water vapor passes through a demister to the plate type vapor condenser, where it condenses and is discharged to the fresh water storage tank by the distillate pump. Throughout operation, the feed rate to the evaporator is fixed by an orifice plate.


If the salinity of the fresh water exceeds a predetermined value, typically a maximum of 10 ppm, a solenoid controlled dump valve diverts the flow to the bilge to prevent contamination of the produced water. Excess salinity can result from several factors, including seawater leakage at the condenser, priming of the evaporator, malfunctioning of the demister, or a drop in vacuum within the chamber.

Gases that cannot be condensed at the condenser, primarily air, are called uncondensable gases and are continuously removed by the air ejector. This keeps the shell at high vacuum, which is essential for boiling water at low temperatures.

Main Components

  • A fabricated steel shell, internally coated with rubber

  • A titanium plate type heater, which functions as the evaporator

  • A titanium plate type condenser

  • A knitted Monel wire demister

Freshwater Generator: Shell and Tube Type

This design is a package unit built to produce fresh water from seawater under vacuum, using either jacket cooling water or steam as the heating medium.

Construction Details

  • The shell is fabricated from steel or a non-ferrous metal such as cupro-nickel, with an internal coating

  • The heat exchanger is arranged as a vertical tube stack

  • The demister consists of a close knit synthetic mesh, typically knitted Monel wire

  • The condenser is a shell and tube type unit

  • Both the condenser and evaporator use aluminum brass tubes and muntz metal tube plates


Other Fitted Components

  • A salinometer to detect salinity of the condensate

  • A combined brine and air ejector

  • A condensate, or distillate, pump

  • An ejector pump

  • A vacuum gauge

  • A relief valve

  • A gauge glass for condensate level

  • A feed water flow controller, in the form of an orifice plate


Principle of Operation

Heat source: Primarily uses main engine jacket cooling water to provide heat for evaporation.

  • Steam operation: When the vessel is in port, steam can be used as an alternative heat source, generally for emergencies.

  • Water produced using steam in port should be used only for washing purposes, not drinking.

  • Economical operation: No additional heat source is normally required because the jacket cooling water provides the necessary heat.

Vacuum Creation

  • An air and brine ejector, operated by the ejector pump, creates a vacuum inside the evaporator shell.

  • The ejector automatically maintains the required vacuum conditions.

  • Due to the vacuum, the boiling point of seawater is significantly reduced.

Evaporation Process

  • Feed seawater enters through the flow controller into the lower chamber of the evaporator.

  • Seawater passes through the heat exchanger tubes, where it is heated.

  • Jacket cooling water or steam flows outside the heat exchanger tubes.

  • The heated seawater evaporates under vacuum.

  • The produced water vapour rises through the evaporator shell.

Demisting & Brine Removal

  • The vapour passes through a demister.

  • The demister separates seawater droplets from the vapour.

  • Separated seawater is discharged as brine through the water ejector.

Condensation

  • The saturated vapour enters the seawater-cooled condenser.

  • Vapour condenses on the outside of the condenser tubes.

  • The condensed water becomes fresh/distilled water.

  • Fresh water collects at the bottom and flows to the distillate pump.

Salinity Control

  • A salinometer continuously monitors the salinity of the produced fresh water.

  • If salinity exceeds the preset limit:

    • A solenoid valve operates.

    • High-salinity water is prevented from entering the fresh-water storage tank.

  • The system maintains produced water at below 10 ppm salinity.

Temperature Changes

  • Jacket cooling water:

    • Inlet temperature: approximately 60–90°C

    • Temperature drop through evaporator: approximately 4–13°C

    • Depends on the cooling-water flow rate.

  • Seawater through condenser:

    • Temperature rise: approximately 6–16°C

    • Depends on the selected flow rate.


Key Parts of a Fresh Water Generator Explained


  1. Heat Exchanger: Allows heat to move from a high temperature medium to a low temperature medium without direct contact between the two. One medium loses heat while the other gains it. Heat exchangers are typically built from segregated elements in the form of plates or tubes with high thermal conductivity.

  2. Demister: A thickened layer of mesh structure fitted between the evaporator and condenser elements, used to separate seawater from the steam vapor. Demisters can be made from nickel, Monel metal, copper, stainless steel, or synthetic fibers such as polypropylene and PVC. Monel metal demisters are the typical choice for fresh water generators.

  3. Ejector Pump: Combines the brine and air ejectors, functioning similarly to an eductor with no moving parts. The seawater pump supplying operating water to these ejectors is often considered part of the ejector pump system as well.

  4. Distillate Pump: A standard centrifugal pump located at the lowest part of the generator. It draws suction from the steam condensate and discharges it to the ship's drinking water tank, with the output passing through a salinometer to check salt content.

  5. Salinometer: Detects even minimal salt content in the sampling water. It sits just before the solenoid operated three way valve and feeds its readings to the control panel, which then routes the water either to storage or back to the generator based on the required salinity limit.

  6. Sea Water Pump: Since both ejectors work on the venturi principle, they require operating water. The seawater pump provides this, generating suction pressure for the ejectors while also supplying feed water for the generator.

  7. Control Panel: Automates the starting and stopping procedures for the machinery, letting the crew monitor operations, start and stop the unit, test alarms, test the salinometer, and set the desired ppm level.


Starting Procedure for a Fresh Water Generator

  1. Confirm the ship is not in congested waters or canals and is at least 20 nautical miles from shore, since effluents and sewage discharged near the coast could enter the generator

  2. Confirm the engine is running at full sea speed, since at low rpm the jacket water temperature, around 60 degrees Celsius, is insufficient for evaporation

  3. Check that the drain valve at the bottom of the generator is closed

  4. Open the suction and discharge valves of the seawater pump, which supplies water for evaporation, cooling, and the eductor for vacuum generation

  5. Open the seawater discharge valve that returns water to the sea after circulation

  6. Close the vacuum valve at the top of the generator

  7. Start the seawater pump and check its pressure, which is generally 3 to 4 bar

  8. Wait for vacuum to build, targeting at least 90 percent as shown on the gauge, which typically takes about 10 minutes

  9. Once vacuum is achieved, open the valve for feed water treatment to prevent scale formation on the plates

  10. Slowly open the jacket water inlet and outlet valves to about half, opening the outlet valve first and then the inlet valve, then gradually increase to full open

  11. Observe the boiling temperature increasing and the vacuum beginning to drop

  12. A vacuum drop to around 85 percent indicates evaporation has started

  13. Open the valve from the fresh water pump to drain

  14. Switch on the salinometer if it requires manual start, though it is generally set to auto start

  15. Start the fresh water pump and taste the water coming from the drain

  16. As fresh water production begins, the boiling temperature will drop slightly again and vacuum will return to normal

  17. Check that water from the salinometer is not salty and confirm the reading is correct, keeping the value below 10 ppm

  18. Once the water taste is confirmed, open the valve to the tank from the pump and close the drain valve


Stopping Procedure for a Fresh Water Generator

  1. Open the bypass valve first, then close the jacket water inlet valve, followed by the outlet valve

  2. Close the feed water treatment valve

  3. Stop the fresh water pump and close its valves

  4. Switch off the salinometer

  5. Stop the seawater pump, or ejector pump, after about 5 minutes

  6. Open the vacuum valve

  7. Close the seawater suction valve and overboard valve, even though these are generally non-return valves, as a precaution against leaking or damage


Scale Formation in Fresh Water Generators

Scale formation reduces the performance of a fresh water generator because it lowers heat transfer efficiency. Three types of scale are commonly found:

  • Calcium Carbonate (CaCO3): Predominates when seawater is heated below 80 degrees Celsius

  • Magnesium Hydroxide (Mg(OH)2): Deposited when seawater is heated above 80 degrees Celsius

  • Calcium Sulphate (CaSO4): Formation depends mainly on the density of the evaporator contents, or brine, rather than temperature


Minimizing Scale Formation

Scale formation can be controlled through continuous chemical treatment. Polysulphate compounds, such as sodium polysulphate combined with an anti-foam agent, are preferred by marine engineers and widely used on ships. These chemicals reduce calcium carbonate scale and the risk of foaming, and the compound itself is non-toxic and non-acidic, making it safe for use in generators producing drinking water.


The chemical is fed continuously into the feed line using a metering pump or by gravity, with the dosage depending on the capacity of fresh water produced. This treatment is only effective in low pressure fresh water generators where seawater temperature stays below 90 degrees Celsius, and it must be carried out consistently to maintain generator performance.

Single Effect and Double Effect Evaporation


A conventional evaporator is heated by steam, which condenses and transmits heat energy to the solution being evaporated. As the solution boils, it releases vapor. If this vapor is condensed in a separate condenser, the process is known as single effect evaporation.


A multiple effect evaporator is an apparatus that uses the heat from steam more efficiently to evaporate water. In this design, water is boiled in a sequence of vessels, each held at a lower pressure than the one before it. Since the boiling point of water decreases with pressure, the vapor produced in one vessel can be used to heat the next vessel in the sequence, improving overall efficiency.


Flash Process (Flash Evaporator)

A flash evaporator heats water in one compartment before releasing it into a second compartment held at substantially lower pressure, causing part of the water to flash into vapor. In this process, sensible heat is supplied rather than latent heat.

The temperature at which water boils is directly related to its pressure. For example, water boils at 100 degrees Celsius at atmospheric pressure, 1.013 bar. This principle is applied in the flash evaporator, where heated seawater is led into a vessel held at sub-atmospheric pressure. It flashes into steam, is condensed by tubes circulated with the salt feed, and is removed by a distillate pump. Baffles and demisters, positioned appropriately, prevent carry over of saline droplets, and purity monitoring arrangements are similar to those used in boiling evaporators.

Osmosis and Reverse Osmosis

Osmosis


Osmosis is a natural phenomenon in which solutions of different concentrations, separated by a semi-permeable membrane, flow from the lower concentration solution to the higher concentration one. In simpler terms, it describes the natural migration of water from one side of a semi-permeable membrane into a solution on the other side.


A semi-permeable membrane acts like a filter, allowing only lighter molecules through while blocking the larger molecules of the dissolved substance. This flow continues until the hydrostatic head of the concentrated solution becomes high enough to stop the process, a point known as osmotic pressure for that particular concentration. For seawater, osmotic pressure is around 28 bar.


Reverse Osmosis


Reverse osmosis reverses this natural process to produce fresh water. It is a water filtration method that uses semi-permeable membrane materials. Seawater on one side of the membrane is pressurized by a pump and forced against the material. Pure water passes through, but the membrane blocks the salts.

The pressure required to force pure water through the membrane is also called osmotic pressure, and higher salinity requires higher pressure. To produce large volumes of pure water, the membrane area must be large and tough enough to withstand pump pressure. Since seawater feed is continuously supplied at a steady salinity, the required osmotic pressure remains steady as well, allowing a continuously running pump to supply consistent pressure.


Cartridge Design


The man-made membrane material used for seawater purification is produced as thin polyamide or polysulphonate sheets, which are not strong enough on their own. To combine a large surface area with adequate reinforcement, these sheets are formed into spirally wound cartridges, housed in tubes made of stainless steel or other suitable material.

The output of a reverse osmosis plant is determined by the number of cartridge tubes arranged in parallel, while quality can be improved by installing sets of tubes in series. Since deposits can gradually block any filtration system, the cartridges are designed so that seawater feed passes through the spiral windings and over the membrane sheets with a washing action that helps keep the surfaces free of deposits. Water produced through reverse osmosis requires the same subsequent treatment as water produced by low temperature evaporators to make it potable.


Treatment of Fresh Water for Drinking


Due to the low operating temperatures in low pressure fresh water generators and flash evaporators, the water produced may not be immediately safe to drink. The following treatments are typically required:

  1. Heating: Heat the fresh water to a sterilization temperature of around 80 degrees Celsius

  2. Chlorination: Sterilize the water by adding sodium hypochlorite at around one ppm

  3. Ultra-violet light: Use UV rays to sterilize the water. This method is ineffective if the water contains particles that shield organisms from the light, so it requires very clean water with no turbidity. While instantly effective, UV sterilization does not prevent re-infection during storage, so it is used alongside other methods rather than alone

  4. Ozone treatment: A highly effective oxidant for sterilization, though the equipment is costly and has high running costs. It is worth noting that if a vessel is within certain coastal limits, seawater may contain harmful effluents from industrial zones that none of these sterilization methods can fully address

Additionally, chemicals or additives used in diesel engine cooling water or seawater systems could be harmful, and in such cases the fresh water produced should not be used for drinking.


Domestic Water System and Treatment Plant


A ship's domestic water system typically comprises a fresh water system for washing and drinking and a separate salt water system for sanitary purposes. Both use a similar arrangement: an automatic pump supplies liquid to a tank pressurized by compressed air, which provides the head needed to deliver water on demand. The pump starts automatically via a pressure switch that activates as water level falls to a predetermined point. The fresh water system additionally includes a calorifier, or heater, usually heated with steam.


System Operation

The tank is filled with compressed air.

  • When the tank is full, pressure is about 3.5 bar.

  • At 3.5 bar, the pump remains OFF.

  • When a tap is opened, compressed air pushes water out of the tank.

  • As water level falls, the pressure also falls.

  • At about 2.5 bar, the pressure switch starts the pump.

  • The pump fills the tank back to the upper level.

  • Pressure rises to about 3.5 bar, and the pump stops.

  • If air pressure is too low, the pump will start and stop frequently.

  • If there is little or no air pressure, the pump may start even for small water leaks.

  • If air pressure is too high, air may come out through the taps with the water.

  • Drinking and cooking water must meet strict purity standards.

  • Therefore, additional water treatment may be required before drinking.


Treatment Plant Process

A typical treatment plant suitable for a general cargo ship sterilizes water with an excess dose of chlorine from hypochlorite tablets. The water is then de-chlorinated by passing through a bed of activated carbon, which removes excess chlorine along with any residual color, taste, or odor. An excess dose of chlorine is applied initially to ensure complete sterilization occurs before the de-chlorination step.


Frequently Asked Questions

What is the difference between an evaporator and a fresh water generator?

The terms are often used interchangeably in marine engineering. Both refer to equipment that produces fresh water from seawater through evaporation and condensation. The evaporator is technically the heat exchanger element that boils the seawater, while the fresh water generator refers to the complete package, including the condenser, demister, pumps, and control system.


Why does a fresh water generator operate under vacuum?

Operating under vacuum lowers the boiling point of seawater significantly, often to between 40 and 60 degrees Celsius. This allows the generator to use low grade heat sources, such as diesel engine jacket cooling water, instead of requiring dedicated high temperature steam, making the process far more energy efficient.


What causes high salinity readings in the produced water?

Several factors can cause excess salinity, including leakage of seawater at the condenser, priming of the evaporator, malfunction of the demister, or a drop in vacuum within the chamber. When salinity exceeds the set limit, typically 10 ppm, a solenoid controlled valve automatically diverts the water to bilge rather than the storage tank.


Why can water not be produced close to shore?

Ships are generally required to be at least 20 nautical miles from shore before starting the fresh water generator, since effluents and sewage discharged near the coast can contaminate the seawater feed and, in turn, the produced fresh water.


Why must the engine be running at full sea speed before starting the generator?

At low engine rpm, jacket cooling water temperature is only around 60 degrees Celsius, which is not sufficient to evaporate seawater efficiently. Full sea speed ensures the jacket water is hot enough to drive the evaporation process.


What causes scale formation, and how is it minimized?

Scale forms from calcium carbonate below 80 degrees Celsius, magnesium hydroxide above 80 degrees Celsius, and calcium sulphate depending on brine density. Scale is minimized through continuous dosing of chemical treatment, typically sodium polysulphate with an anti-foam agent, fed into the feed line via a metering pump.


Is water from a fresh water generator safe to drink immediately?

Not always. Due to the relatively low operating temperatures involved, the water may require additional treatment such as heating to sterilization temperature, chlorination, ultra-violet sterilization, or ozone treatment before it is considered safe for drinking.


What is the difference between distillation and reverse osmosis?

Distillation produces fresh water by evaporating seawater using heat and then condensing the vapor. Reverse osmosis instead uses high pressure to force seawater through a semi-permeable membrane that blocks salt molecules while allowing water through. Distillation relies on heat energy, while reverse osmosis relies on mechanical pressure.


Why is a demister needed in a fresh water generator?

A demister is a mesh layer positioned between the evaporator and condenser that scrubs seawater droplets out of the rising vapor. Without it, salt water particles could carry over into the distilled water, compromising its purity.


What is single effect versus multiple effect evaporation?

In single effect evaporation, vapor produced by boiling is condensed once in a single condenser. In multiple effect evaporation, several vessels are arranged in sequence, each at a lower pressure than the last, so the vapor from one vessel can be reused to heat the next, improving overall energy efficiency.


Can fresh water generators be used while the ship is in port?

Generally, fresh water generators are designed to run on jacket cooling water while the engine is operating at sea. In port, water can be produced using steam instead, but this is usually reserved for emergencies, and water produced this way is recommended for washing purposes only, not for drinking.


Write to us at hello@dmetclub.com for any assistance

© 2024 Dmet Club, Powered by Xofy Tech

bottom of page