Governor and Overspeed Trip on Marine Engines: Working Principle, Types & Safety | MEO Class 4

Introduction
A marine diesel engine must maintain the correct speed under changing load conditions. When the load on an engine increases or decreases, its speed also tends to change. Without an automatic speed-control arrangement, the engine may run too slowly, become unstable or exceed its permitted operating speed.
This is where the marine engine governor plays an important role. It automatically regulates the fuel supplied to the engine to maintain the required speed or respond to changes in operating conditions.
Along with the governor, an overspeed trip provides an additional safety measure by shutting down the engine if its speed rises beyond the specified limit.
For marine engineering cadets, understanding governor working, types, speed droop, hunting and overspeed protection is important for both engine-room operations and MEO Class 4 examinations.
1. What Is a Governor in a Marine Diesel Engine?
A governor is a mechanical or electro-mechanical device that automatically controls engine speed by regulating the quantity of fuel injected into the engine.
Its main purpose is to maintain the required engine speed when the load changes.
For example:
When engine load increases, engine speed tends to decrease.
The governor senses the reduction in speed.
It increases fuel delivery to produce the additional power required.
When the load decreases, the governor reduces fuel delivery to prevent excessive speed.
In this way, the governor continuously adjusts fuel supply according to the engine's operating requirements.
Why Is a Governor Required?
A governor is necessary because the load on a marine diesel engine is not always constant.
It helps to:
Maintain the required engine speed.
Regulate fuel supply according to load changes.
Prevent excessive speed variations.
Improve engine stability.
Support safe and reliable engine operation.
For auxiliary generator engines, maintaining a nearly constant speed is particularly important because engine speed directly affects the frequency of electrical power generated.
2. Basic Components and Working Principle of a Governor
To control engine speed, a governor must perform three basic functions:
Speed sensing: Detect the actual running speed of the engine.
Speed comparison: Compare actual speed with the desired or set speed selected by the operator.
Fuel regulation: Adjust fuel delivery according to the difference between actual and set speed.
This is known as a closed-loop control system.

How Does the Closed-Loop Control Work?
The engine speed acts as feedback to the governor.
The governor compares the measured speed with the selected speed and produces a corrective action.
If actual speed is below the set speed, fuel delivery is increased.
If actual speed is above the set speed, fuel delivery is reduced.
When the required speed is reached, the governor returns to an equilibrium condition.
The ordinary mechanical governor works as a proportional controller in this closed-loop arrangement. Its corrective action depends on the deviation between the actual and desired speed.
3. Types of Governors Used in Marine Diesel Engines
The presentation explains two main governor arrangements:
Mechanical governor
Mechanical-hydraulic governor
A. Mechanical Governor
A conventional mechanical governor uses centrifugal force to sense changes in engine speed.
Main components:
Two rotating flyweights.
Crank levers and supporting pivots.
Rotating stool driven through the engine gearing.
Adjustable governor spring.
Axial thrust bearing.
Collar and speeder rod.
Fuel control lever or fuel rack connection.

Working principle:
The governor stool rotates with the engine through a gear-driven arrangement. As the flyweights rotate, centrifugal force acts on them and causes their radial position to change.
This movement is transferred through the crank levers to the collar and speeder rod.
The speeder rod then controls the fuel rack of the fuel injection pumps, regulating the quantity of fuel injected into the engine.
When engine speed increases:
Centrifugal force on the flyweights increases.
The flyweights move outwards.
The speeder rod moves.
Fuel delivery is reduced.
Engine speed comes back towards the required value.
When engine speed decreases:
Centrifugal force on the flyweights decreases.
The flyweights move inwards.
The speeder rod moves in the opposite direction.
Fuel delivery is increased.
Engine speed rises towards the required value.
Equilibrium Condition
When the engine is running at a steady speed, the centrifugal force produced by the rotating flyweights balances the force exerted by the governor spring.
The speeder rod remains stationary, the fuel rack stays in its required position and the engine operates at equilibrium speed.
Changing the Set Speed
The set speed can be changed by adjusting the compression of the governor spring.
In the arrangement described in the presentation, a handwheel is used for this purpose. An electric motor or pneumatic piston may also be used to allow remote speed adjustment.
Limitation of a Mechanical Governor
An ordinary mechanical governor has limited sensitivity and may allow different steady speeds under different loads. This characteristic is known as offset in proportional control.
It may also lack sufficient force to move the fuel control mechanism of a large engine directly.
This leads to the use of a mechanical-hydraulic governor.
B. Mechanical-Hydraulic Governor
A mechanical-hydraulic governor combines the speed-sensing action of a mechanical governor with hydraulic power assistance.
The small force produced by the difference between the spring force and centrifugal force may not be sufficient to move the fuel racks of a large engine.
To overcome this limitation, a Servo Power Amplifier (SPA) is used.
The SPA provides the additional hydraulic force required to move the fuel control mechanism.
This arrangement is also called a relay-type governor.
Main functions:
Mechanical flyweights sense changes in engine speed.
The spring and flyweight mechanism compares actual speed with the set speed.
The pilot valve controls the movement of hydraulic oil.
The servo piston provides the force required to move the fuel control lever.
A feedback mechanism helps bring the pilot valve back towards its neutral position.

Working of a Mechanical-Hydraulic Governor
Consider a sudden increase in engine load.
The engine speed begins to decrease due to the increased load.
The centrifugal force acting on the flyweights decreases.
The flyweights move inwards and the speeder rod moves downwards.
The pilot piston moves, allowing pressurised oil to act beneath the servo piston.
The servo piston moves and provides the required force to increase fuel delivery.
The fuel control lever moves to supply more fuel to the engine.
As the engine responds, the feedback lever reduces the spring force and brings the pilot valve back towards its neutral position.
The additional hydraulic force allows the governor to operate the fuel control mechanism quickly and effectively.
Fail-Safe Arrangement:
The supplied presentation describes a fail-safe arrangement in which failure of the governor mechanism results in engine shutdown. The exact shutdown arrangement depends on the governor and engine design.
4. Speed Droop in Marine Engine Governors
Speed droop refers to the difference between the no-load speed and full-load speed of an engine.
It allows the engine to operate at a lower speed as the load increases.
The percentage speed droop is calculated as:
Speed Droop (%) = (No-load Speed − Full-load Speed) ÷ No-load Speed × 100
Where:
No-load Speed = Engine speed at no load (RPM)
Full-load Speed = Engine speed at full load (RPM)
For example, if an engine operates at 1,500 RPM at no load and 1,470 RPM at full load:
[\frac{1500-1470}{1500}\times100=2%]
Therefore, the speed droop is 2%.

Why Is Speed Droop Required?
Speed droop is particularly important in auxiliary generator engines.
When two or more generators operate in parallel, droop characteristics help them share the electrical load.
It allows the engine speed to reduce slightly as load increases, providing a stable basis for load sharing.
Why is droop generally not required in main propulsion engines?
Auxiliary engines drive generators and require stable electrical frequency.
Droop helps multiple generators share the load.
Main propulsion engines operate at different speeds according to propulsion requirements.
They do not normally require generator-style load sharing.
The amount of droop and its settings depend on the engine and governor arrangement.
5. Hunting and Stability in Marine Engine Governors
What Is Hunting?
Hunting is the continuous fluctuation of engine speed and fuel delivery above and below the required value following a change in load.
It occurs when the governor overcorrects the speed deviation.
How does hunting occur?
Consider a sudden increase in engine load:
Engine speed decreases.
The governor senses the speed drop and increases fuel delivery.
Due to mechanical inertia and friction, the corrective action is delayed.
Fuel delivery may increase more than required, causing engine speed to rise above the desired value.
The governor then reduces fuel delivery.
It may again overcorrect, causing speed to fall below the required value.
This repeated overshooting and undershooting is known as hunting.
If the instability becomes severe, engine speed may reach the overspeed trip setting.
How Can Hunting Be Reduced?
In the mechanical-hydraulic governor arrangement described in the presentation, a feedback lever helps reduce hunting.
As the servo piston moves the fuel control mechanism, the feedback linkage acts on the pilot valve and brings it towards its neutral position.
This reduces excessive corrective action and helps the engine settle at the required speed.
Speed droop is another governor characteristic used to improve stability and support load sharing in generator applications.
What Is Governor Stability?
A governor is considered stable when there is only one radius of rotation of the flyweights for each operating speed within its speed range.
Stability ensures that the governor responds in a controlled manner rather than continuously fluctuating.
What Is Governor Sensitivity?
Sensitivity is the ability of a governor to control engine speed within narrow limits.
A sensitive governor produces a comparatively large speeder rod movement for a small change in the radial position of the rotating flyweights.
In a conventional mechanical centrifugal governor, increasing sensitivity can reduce stability. Therefore, a balance between sensitivity and stability is important.
What Is Governor Effort?
Governor effort is the resultant force acting on the speeder rod due to the difference between the spring force and centrifugal force.
At equilibrium, when there is no change in load or speed, the resultant effort is zero.
6. Overspeed Trip Device in Marine Diesel Engines
The governor regulates engine speed during normal operation. However, an overspeed trip is an independent safety feature provided to protect the engine against excessive speed.
A governor and an overspeed trip have different functions:
Governor: Controls engine speed by regulating
fuel delivery.
Overspeed trip: Shuts down the engine when its speed exceeds the specified safety limit.

Why Is an Overspeed Trip Required?
If the engine speed rises beyond its permitted limit, excessive mechanical stresses may develop in rotating and reciprocating components.
An overspeed trip provides protection by stopping the engine before the speed reaches a dangerous level.
Working of the Overspeed Trip
According to the supplied presentation:
The overspeed trip is an additional safety feature in large marine engines.
It is separate from the normal governor.
The trip operates when engine speed exceeds the maximum rated speed by approximately 15%, as stated in the presentation.
Once tripped, the engine remains shut down.
The trip must be reset before the engine can be restarted.
The device is located on the camshaft extension in the arrangement shown in the presentation.
The actual trip setting, mechanism and reset procedure must always be checked against the engine manufacturer's instructions.
Important: An overspeed trip is not a substitute for a properly functioning governor. Both systems serve different purposes and are important for safe engine operation.
7. Common Governor Problems and Their Effects
Governor problems can affect engine speed, fuel delivery and overall engine stability.
Problem | Possible effect |
Incorrect governor adjustment | Engine runs above or below the required speed |
Governor hunting | Continuous fluctuation in RPM |
Excessive friction in moving parts | Delayed governor response |
Hydraulic oil leakage | Reduced servo performance |
Pilot valve sticking | Incorrect or delayed fuel adjustment |
Feedback mechanism malfunction | Poor speed stability and increased hunting |
Governor mechanism failure | Loss of speed control; shutdown may occur in fail-safe arrangements |
Important Checks During Governor Inspection
During inspection and maintenance, attention should be given to:
Condition of flyweights, pivots and linkages.
Free movement of the speeder rod.
Governor spring condition and adjustment.
Hydraulic oil condition and leakage in hydraulic governors.
Pilot valve and servo piston movement.
Fuel control linkage and feedback mechanism.
Overspeed trip setting and resetting arrangement.
All inspection, testing and adjustment should be carried out according to the manufacturer's manual and the vessel's safety management procedures.
8. Difference Between Governor and Overspeed Trip
Governor | Overspeed Trip |
Controls normal engine speed | Protects against excessive engine speed |
Regulates fuel delivery | Initiates engine shutdown |
Operates continuously during engine operation | Operates when the specified trip speed is exceeded |
Maintains the required speed according to load and setting | Prevents continued operation at dangerous speed |
Part of the normal speed-control system | Additional independent safety protection |
9. MEO Class 4 Questions and Answers
Q1. What is the function of a governor in a marine diesel engine?
A governor automatically controls engine speed by regulating the quantity of fuel supplied to the engine.
Q2. What are the three basic functions of a governor?
Speed sensing, comparison of actual and set speed, and fuel regulation.
Q3. What is a mechanical governor?
A mechanical governor uses centrifugal force acting on rotating flyweights to sense changes in engine speed and operate the fuel control mechanism.
Q4. Why is a Servo Power Amplifier used in a mechanical-hydraulic governor?
The SPA provides the additional hydraulic force required to move the fuel control mechanism of a large engine.
Q5. What is hunting?
Hunting is the repeated fluctuation of engine speed and fuel delivery above and below the required value due to overcorrection by the governor.
Q6. What is speed droop?
Speed droop is the percentage difference between the no-load speed and full-load speed of an engine.
Q7. Why is speed droop used in auxiliary generator engines?
It helps generators operating in parallel share electrical load in a stable manner.
Q8. Define governor sensitivity.
Sensitivity is the ability of a governor to control engine speed within narrow limits.
Q9. What is governor stability?
A governor is stable when there is only one flyweight radius of rotation for each operating speed within its operating range.
Q10. What is the difference between a governor and an overspeed trip?
A governor regulates fuel delivery to control normal engine speed, whereas an overspeed trip shuts down the engine when its speed exceeds the specified safety limit.
Q11. At what speed does the overspeed trip operate?
The supplied presentation specifies approximately 15% above maximum rated speed. Always confirm the actual setting from the engine manufacturer's documentation.
Conclusion
The governor is an essential part of marine diesel engine speed control. It senses changes in engine speed and regulates fuel delivery to maintain the required operating conditions.
Mechanical governors use centrifugal force and spring action, while mechanical-hydraulic governors use a servo power amplifier to provide the additional force needed to operate large-engine fuel controls.
Understanding speed droop, hunting, sensitivity, stability and feedback helps marine engineering cadets understand how governors respond to changing engine loads. The overspeed trip provides an additional layer of protection by shutting down the engine when its speed exceeds the specified limit.
For MEO Class 4 preparation, a clear understanding of the governor's working principle and its difference from the overspeed trip is particularly important.



